Did you mean: High pressure (Technology) TECHNICAL PRESS Ieee press series on rf and microwave technology. The technical press ltd The Technical Press Ltd London CRC Press advanced and emerging communications technologies series IEEE Press understanding science & technology series MANUFACTURING TECHNOLOGY PRESSURE VESSELS DESIGN AND CONSTRUCTION ACC NO-30533 IEEE Computer Society Press technology series The CRC Press advanced and emerging communications technologies series The Dryden Press series in computer technologies Cisco Press networking technology series Focal Press media technology professional AUTOMOTIVE SILICON SENSOR INTEGRATION 1-6 SILICON MICROSTRUCTURES MERGING MECHANICS WITH ELECTRONICS 7-16 A MICROMACHINED SILICON MASE AIR FLOW SENSOR 17-24 NEW TECHNOLOGIES FOR SILICON ACCELEROMETERS ENABLE AUTOMOTIVE APPLICATIONS 25-32 VEHICLE ACCELERATION SENSOR APPLIED WITH MAGNETIC FLUID 33-40 PIEZORESISTIVE ACCELERATION SENSOR FOR AUTOMOTIVE APPLICATIONS 41-46 ACCELERATION SENSOR FOR ABS 47-54 POWER RATE CRASH SENSING METHOD FOR DEVICE ACTUATION 55-60 A PREDICTIVE BASED ALGORITHM FOR ACTUATION OF AN AIRBAG 61-66 AUTOMOBILE CRASH MODELING AND THE MONTE CARIO METHOD 67-72 A HEAD CLEARANCE MEASUREMENT SYSTEM USING IMAGE PROCESSING 73-82 NEAR INFRARED ABSORPTION SENSOR FOR IN VEHICLE DETERMINATION OF AUTOMOTIVE FUEL COMPOSITION 83-98 TWO ALTERNATIVE DIELECTRIC EFFECT FLEXIBLE FUEL SENSORS 99-110 OIL PRESSURE SENSOR USING AMORPHOUS MAGNETIC ALLOY 111-118 A CYLINDER PRESSURE SENSOR FOR INTERNAL COMBUSTION ENGINE 119-124 ENGINE KNOCK DETECTION USING MULTI SPECTRUM METHOD 125-130 THROTTLE POSITION SENSOR TERMINATION AND CONNECTOR RELIABILITY 131-140 FIBRE OPTIC GYROSCOPE FOR AN AUTOMOBILE NAVIGATION SYSTEM 141-150 ATOMIZATION CHARACTERISTICS OF TWO STREAM INJECTOR FOR 4 VALVE ENGINES 151-158 TESTING AND EVALUATION OF INJECTION MOLDED MAGNETS IN ENGINE AND IGNITION ENVIRONMENTS 159-172 DEVELOPMENT SYSTEMS 159-172 DEVELOPMENT OF A NON CONTACT TORQUE TRANSDUCER FOR ELECTRIC POWER STEERING SYSTEMS 173-183 ACC NO-27353 ACC NO-30830 ACC NO-30831.SP-903 A NEW MATERIAL FOR NEW WAYS OF DESIGN 1-6 A SHEET METAL STAMPING CLASSIFICATION SYSTEM FOR PRODUCT PROCESS 7-18 CAPABILITIES AND ADVANCES IN THE FINEBLANKING PROCESS 19-40 SHEARING AND STAMPING HOT ROLLED MATERIAL 41-50 COMPUTERIZED CONTROL OF THE BLANKHOLDER PRESSURE ON DEEP 51-56 TRIBOLOGICAL FACTORS AFFECTING THE LDH TEST 57-62 GLOBAL AND LOCAL PERSPECTIVES OF GRID ANALYSIS TECHNIQUES 63-72 COMPARISON OF DIFERENT SURFACE STRAIN MEASUREMENT METHODS USED FOR DEFORMED SHEET METAL PARTS 73-86 RECENT PROGRESS IN THE DEVELOPMENT OF FORMING LIMIT CURVES FOR AUTOMOTIVE SHEET STEELS 87-104 INTERACTION OF PART GEOMETRY AND MATERIL PROPERTIES WITH FORMING SEVERITY AND TOOLING DESIGN FOR BOX SHAPED STAMPINGS 105-114 MICRO MECHANISTIC INTERPRETATION OF TOOL WORKPLACE INTERACTIONS 115-122 EFFECT OF BEAD FINISH ORIENTATION ON FRICTION AND GALLING IN THE DRAWBEAD TEST 123-134 AN EVALUATION OF INTERFACE FRICTION IN DIFERENT FORMING MODELS FOR COATED STEEL SHEETS 135-142 TRANSIENT TRIBOLOGICAL PHENOMENA IN DRAWBEAD SIMULATION 143-150 THE EFFECTS OF DIE MATERIALS AND ELECTRO ETCHING ON FRICTIONAL CHARACTERISTICS OF AUTOMOTIVE SHEET STEELS 151-160 USING AXISYMMETRIC SOLUTIONS TO ESTIMATE THE FORMING SEVERITY OF THREE DIMENSIONAL METAL STAMPINGS 161-172 FACTORS AFFECTING THE FORMABILITY OF CORNERS IN SHEETMETAL PARTS 173-182 ON A ONE STEP FINITE ELEMENT APPROACH FOR A CLOSER INTERFACE BETWEEN PRODUCT DESIGN AND MANUFACTURING FEASIBILITY 183-192 NUMERICAL SIMULATION OF A STRETCH DRAWN AUTOBODY PART 1 ASSESSMENT OF SIMULATION METHODOLOGY AND MODELING OF STAMPING COMPONENT 193-206 NUMERICAL SIMULATION OF A STRETCH DRAWN AUTOBODY PART-2 VALIDATION VERSUS EXPERIMENTS FOR VARIUOS HOLDING AND DRAWBOARD CONDITIONS 207-219 ACC NO-27350 ACC NO-30802 ACC NO-30801 ACC NO-28044